Recently my husband I bought a set of Ikea Borge chairs for our dining room. The chairs looked great but I knew the white canvas seats the come with wouldn’t last long in a house with two little boys and frequent dinner guests! I did some searching online and came to the Harts Fabric website. After looking at their amazing selection of fabrics and laminated cottons, I contacted Harts to see if they’d be interested in partnering with me for this post. Luckily they were and I chose this great Riley Blake BPA Free Aqua Hexies. That fabric is now out of stock but they still have the yellow in stock along with a huge selection of other laminated cottons! Here’s an image of just a small selection of the ones they have.
I tried covering the chairs two ways so I’ll lead you through the process for either stapling the fabric directly to the chair seat, or sewing a slipcover with elastic. These instructions include measurements specifically for the Ikea Borge chairs, but they could be modified for whatever chair you have.
Stapled Seat Cover
Let’s begin with the easy one, stapling! I used a staple gun with 1/4″ staples. For each seat, cut a rectangle 22″ wide (the fabric total width is 44″ so you can get 2 widthwise) by 20.5″ long (this measurement is along the selvage edge). These measurements give you 2″ to wrap around the back of the chair and 2 1/2″ for the other 3 sides.
To begin, lay the top of the seat against the wrong side of the fabric. Position the 22″ side of the fabric just beyond the screw holes at the back of the seat and place one staple in the center. Then put 2 more staples to either side of the center one for a total of 5 staples about 1 1/2″ apart. Hammer down any staples that are sticking up at all. Any of the photos in this post can be clicked on for a larger view.
Stretch the fabric to remove any wrinkles and staple it to the front of the chair with 5 staples starting in the center and moving out to the sides 2″ apart. Then stretch the sides and do a row of staples on each side, starting in the center and moving out to the sides for a total of 5 staples 1 1/2″ apart.
Next staple down the front corners. On the back of the chair, first fold one piece of fabric tight toward the corner and staple down. Fold the other flap toward the corner and staple down. Next take the triangular flap you’ve just created and pull it tightly toward the middle of the chair and staple it down. From the top it will look slightly rounded and have 1 small fold on each side of the corner.
Last, staple down the back corners. This is a little tricky as there is a notch cut out for the back of the chair. From the back of the chair, fold the fabric from the back edge of the seat toward the middle of the seat and staple in place. Then fold the fabric from the side of the seat toward the middle until it’s nice and tight. Staple into place. Then take the triangular flap you’ve just created, pull it tight and move any wrinkles into the center of the notch in the seat. Staple into place. When finished your fabric will look nice and smooth with no wrinkles! If you’d like, trim off any excess fabric corners that are sticking out.
Sewn Slipcover Seat Cover
This method took a bit more work. If you are using non-laminated fabric it’s nice that it can be removed to wash, but for these particular chairs you would have to remove the 4 screws holding the seat down before you could remove it. To use this method, first print out my free pattern (this link will open a pdf in a new window you can save or print). Pattern was designed using Ikea Borge chairs purchased May 2015, just in case they change the style in the future! Match up the stars in the pattern and tape the five pattern pages together. To use this pattern your fabric will need a small amount of give so you can stretch it tightly over the corners of the chair. It’s a little tighter than the slipcover that comes with the chair so you’ll have a nice smooth top with the laminated cotton. If you use the pattern, try making just one cover first to make sure it’ll work with your fabric!
To stabilize the fabric, either use a serger along all the edges or a sewing machine to do a zigzag stitch close to the edge. Then fold the fabric on each side (but not the corners) under by 5/8″ and sew with a 1/2″ seam allowance. This will form the casing for elastic. In the photo below you can see I used a roller foot to help the laminated cotton glide more smoothly through my sewing machine. If you don’t have one, you can try putting matte finish Scotch tape on the bottom of a regular sewing foot to keep it from sticking to the fabric.
On the wider side of the fabric (the front of the seat), bring right sides of the corners together and sew with a 1/2″ seam allowance from the fold to just before the casing and backstitch to secure.
On the two remaining corners (the back corners), bring the notched out section of the corner right sides together and sew from 1/2″ away from the edge on the fold, down to the edge of the fabric.
Thread 3/8″ elastic through the casing on all 4 sides. Use a nice firm elastic with around 50% stretch (a 4″ piece will stretch to 6″ before it starts to resist). Start in the back corner and leave at least 5″ sticking out at both the start and finish. Fit the cover around your seat and pull it snug in all directions. Smooth out any wrinkles, pull the elastic tight and then tie it in a knot. If you don’t have firm elastic, string will also work if you tie it in a tight bow so you can un-string it later to get the cover off.
Comparing Both Methods
Both methods worked well and the final seats look nearly identical. Personally, I preferred the staple method as it was faster, easier to get a nice smooth seat with no wrinkles, and uses less fabric. And, with the laminated cotton I’ll never have to take it off to wash, just wipe clean, so laundering isn’t an issue! I also think the stapled seats may also be a bit more stable as I’m a little concerned that all of the thread holes in the sewn version may make it more prone to rip with heavy usage. But, again, these differences are minor enough that in the final chair no one can see a difference! So far we’ve used both versions for the last week with a birthday party and house guests and they look great! The fabric hasn’t stretched to show any wrinkles and the tops all look nice and shiny.
No comments:
Post a Comment